Coolest Emmett Lego Minifigure Costume

A little about my Lego minifigure costume:

My 5 year old son, Riley, loves Legos, and especially The Lego Movie. One night we were discussing what he wanted to be for Halloween and I decided that I would attempt to make him his favorite character from The Lego Movie, Emmett.

Lego Minifigue Costume Supplies

  • Plastic Tupperware-like container from the dollar store that had a similar shape to a Lego head and that also fit over my sons head.
  • Several cans of spray paint (orange, yellow, red and a clear gloss).
  • A hollow Styrofoam half sphere.
  • Lots of cardboard.
  • Duct tape.
  • Masking tape.
  • Permanent markers.
  • Glue.
  • Black plastic mesh (to cover the mouth cutout so my son’s eyes would be less noticeable).
  • Yellow face paint for his neck.
  • A blue shirt and blue pants with orange stripe (fortunately, they came right from his closet).
  • Yellow gloves.

I began making the costume after I found the plastic container that would eventually be the Lego head.

Costume Instructions

  • I drew the spot where my son’s eyes were on the container and from there created the mouth with a black Sharpie.
  • After I was satisfied with the mouth, I began cutting it out (since my son would see out of it). That proved a little difficult and I ruined one plastic container and had to start over with a spare one I had bought. The plastic easily cracked if not cut just right.
  • After I completed cutting out the mouth, I sanded down the edges with sandpaper and then began spray painting the container yellow.
  • After a couple coats of paint, I drew in the eyes and eyebrows with a Sharpie and outlined the mouth as well. I glued the black plastic mesh to the inside so that my son’s eyes would not be as visible.
  • I wasn’t quite sure how I was going to make the hair, but after a trip to Michael’s I found the hollow half Styrofoam sphere and figured I could make the hair out of that. Well, after a little more brainstorming I decided that I would make it into a hat instead and draw the hair on with a brown permanent marker.
  • To make the hat, I sanded down the inside of the Styrofoam sphere so that it would fit better onto the container.
  • Once it was the way I wanted it, I created the bill of the hat out of cardboard and then glued it to the sphere.
  • It was spray painted red and a printed out Lego logo was glued to the front.
  • I attached the hat to the container with glue and then drew in the hair with the brown permanent maker.
  • The body of the costume was made out of cardboard. After I took my son’s measurements, I drew out the shape of the body (the front and back panels and the strip that connected them) onto a piece of cardboard. I cut them out with a knife and made sure the front and back were identical in size and shape.
  • For the side panels I just measured the distance from the two panels (front and back panels) at the top and bottom and created the sides, but I left a little extra to make a glue strip.
  • Everything was glued together and let to dry overnight.
  • In the morning, after my son tried it on, I realized it was too wide and Ihad to take it apart and cut out a few inches from the front and back panels and reassemble it.
  • Before painting it, I covered up the edges with masking tape.
  • Two coats of orange spray paint were needed to get the desired color. The detailing on the front and back panels was done with duct tape and permanent makers. I used Riley’s little Emmett mini-figure as my model.
  • To complete the costume, I spray painted everything with a clear gloss to give it that shiny Lego look.
  • We found a solid blue long sleeve shirt and a pair of blue pants with an orange stripe in Riley’s closet.
  • I bought some yellow body paint for his neck and I ordered a pair of yellow gloves from for his hands.

We haven’t gone trick or treating yet but everyone that I have showed pictures to thinks it looks great! Riley cannot wait to go out trick or treating with his friends to show it off.

This was my first time making any of my children a Halloween costume. Once I got past the brainstorming phase, I found it to be a lot of fun. Most of the work took place after the kids were in bed for the night. I’m pretty proud of it too.



  • Costume Ideas Brainstormer
  • Tags

    Child Cost: $20-$50 Editors Picks Individual Man/Boy Costume LEGO No-Sew